SEKURE DGP2-648 Installation Manual download pdf (Page 18)

16 REFERENCE & INSTALLATION MANUAL

5 KEYSWITCH PROGRAMMING

The DigiplexNE control panel can support up to 32 keyswitch zones in addition to the 96 standard zones. A keyswitch allows a user to arm or disarm a

system by pressing a key or by toggling a keyswitch. A keyswitch can also be used to generate a Utility Key event which can then be used to activate or

deactivate PGM outputs connected to the DigiplexNE system. The keyswitches are connected to the hardwired input terminals of either the control panel,

zone expansion modules or the keypad. For installation instructions, see section 2.9 on page 4. Keyswitches must be programmed as described in this

section (see Figure 5-1). UL Note: Keyswitches are not to be used in UL Listed systems.

Figure 5-1: Keyswitch Programming

5.1 KEYSWITCH NUMBERING

ECTIONS [0501] TO [0532]

Keyswitch Numbering allows you to assign any hardwired input in the

system to any of the 32 keyswitch zones in the control panel. It identifies

where the keyswitch is connected and which keyswitch zone is assigned to

the keyswitch (see Figure 5-2).

Figure 5-2: Example of Keyswitch Numbering

5.2 KEYSWITCH DEFINITIONS

Keyswitch Definitions determine how the control panel reacts when a

keyswitch is activated.

5.2.1 Keyswitch Disabled

SECTIONS [0601] TO [0632]: FIRST DIGIT = 0

Disables keyswitch input.

5.2.2 Momentary Keyswitch

SECTIONS [0601] TO [0632]: FIRST DIGIT = 1

To arm a partition using the Momentary Keyswitch, turn on the keyswitch for

approximately three seconds then turn it off. Repeating this sequence will

disarm the system. The selected Keyswitch Option (see section 5.4)

determines the type of arming.

5.2.3 Maintained Keyswitch

SECTIONS [0601] TO [0632]: FIRST DIGIT = 2

To arm a partition using the Maintained Keyswitch, turn the switch from the

ON to the OFF position. To disarm a partition set the keyswitch in the ON

position. The selected Keyswitch Option (see section 5.4) determines the

type of arming. If the keyswitch’s Arm Only option is enabled, the control

panel will not perform any action when the switch is in the on position.

Press & hold the

[0] key

Enter your

[

INSTALLER CODE]

Enter 4-digit

[

SECTION]

Keyswitch Numbering

Sections [0501] to [0532] represent

keyswitches 1 to 32 respectively

Keyswitch Parameters

Sections [0601] to [0632] represent

keyswitches 1 to 32 respectively

Enter the module’s 8-digit

[

SERIAL NUMBER] where the

keyswitch is installed

Enter the 3-digit [

INPUT

NUMBER] where the

keyswitch is connected

Keyswitch Definition

First Digit

Keyswitch Partition

Assignment

Second Digit

Keyswitch Options

Feature Select

Press [

ENTER]

Keyswitch Definitions

[0] Disabled (default)

[1] Momentary Keyswitch

[2] Maintained Keyswitch

[3] Generates a Utility Key Event on Open

[4] Generates a Utility Key Event on Open & Close

Keyswitch Partition Assignment

[0] Not assigned to partition(s) (default)

[1] Assigned to partition 1

[2] Assigned to partition 2

[3] Assigned to partition 3

[4] Assigned to partition 4

[5] Assigned to partition 5

[6] Assigned to partition 6

[7] Assigned to partition 7

[8] Assigned to partition 8

Keyswitch Options

Default = All OFF

[1] to [3] = Future Use

[4] Stay/Instant Disarm

[5] Arm Only

[6] Stay Arming*

[7] Force Arming*

[8] Instant Arming*

* Select one only; if all are OFF, defaults to regular

arming.

Select one

only

Select one

only

Set

options

Control Panel

SN#: 020000A2

Keyswitch B

Keyswitch C

Keyswitch

Zone # Section Serial# Input#

Keyswitch A: 1 = [0501] 020000A2 001

Keyswitch B: 2 = [0502] 34000041 002

Keyswitch C: 3 = [0503] 34000041 006

Input 2

Input 6

Keyswitch A

Input 1

Input Terminals

1 2 3 4 5 6 7 8

OMMUNICATION

ETWORK

Zone Expansion Module

SN#: 34000041

Input Terminals

1 2 3 4 5 6 7 8

Combus

1 2 ... 13 14 15 16 17 18 19 20 21 22 23 ... 63 64

Comments to this Manuals

No comments

SEKURE DGP2-648 Installation Manual Page 18

Comments to this Manuals

Related products and manuals for Security access control systems SEKURE DGP2-648