SEKURE DGP2-648 Installation Manual download pdf (Page 35)

DIGIPLEXNE CONTROL PANEL 33

Delay, Bell Squawk, One-touch Arming, Panic Alarms and many more. All

zones, keyswitch zones, user codes and system modules are assigned to

specific partitions, making this a true partitioned system. Enable the

option(s) that correspond to the desired partition(s):

11.9.1 Panel Partition Assignment

SECTION [3020]

(Default = 00) The control panel will report system events as originating

from one or all enabled partitions. The System Troubles (i.e. AC Failure,

TLM Failure, etc.) can only be viewed through the partitions enabled in this

section. Enter a 2-digit decimal number from 01 to 08 which represent

partitions 1 to 8. Enter 00 to disable this feature.

11.10 SHABBAT FEATURE

ECTION [3030]: OPTION [4]

(Default = disabled) When option

[4]

is enabled, detectors and keypads in the

system no longer display system status through the LCD and/or LEDs between

noon (12:00PM) Friday and midnight (12:00AM) Saturday. Normal operation is

re-instated Sunday morning at 12:00:01AM. If required, a user can access all

the usual commands and features during the Shabbat period by pressing a key

or by entering their access code (also depending if and how Confidential Mode

is enabled in the keypad). When no actions have occurred for two minutes, the

Shabbat Feature will re-activate. During the Shabbat period:

• the LCD keypads only display the date and time

• the backlight is disabled

• the LED indicators on modules are disabled

11.11 INSTALLER FUNCTION KEYS

Press and hold the [0] key and key in the [INSTALLER CODE] to access the

installer functions and then...

For LCD keypads: Press the key indicated in the list below that

corresponds to the function you wish to activate.

For Grafica keypads: Press the center action key (Options), highlight the

desired function and then press the left action key (Select).

11.12 MODULE RESET

ECTION [4001]

To reset a module connected to the combus to its default values, key in the

module's serial number into section [4001].

11.13 LOCATE MODULE

ECTION [4002]

To locate a specific module on the combus, key in the module's serial

number into section [4002]. The green

LOCATE LED on the module flashes

until the serial number is re-entered into the section or the module’s tamper

or unlocate switch is pressed.

11.14 MODULE PROGRAMMING

ECTION [4003]

All modules connected to the combus are programmed through the control

panel. To program a module, enter section [4003] to enter Module

Programming Mode (see section 3.5), key in the module's serial number

and follow the programming indicated in the DigiplexNE Modules

Programming Guide. To exit this mode, press the [

CLEAR] key until Normal

Mode is displayed.

11.15 MODULE AND LABEL BROADCAST

ECTION [4004]

Module Broadcast

To copy the contents of the programming sections from one module to one

or more of the same type, key in the serial number of the source module in

section [4004], enter the serial numbers of all the destination modules and

press [

ACC] if using an LCD keypad or the center action key (Start) if using

a Grafica keypad.

Label Broadcast

Copy the User Labels, Zone Labels (sections [0301] to [0396]), the Door

Labels (sections [2301] to [2332]) and the Partition Labels (sections

[3100], [3200], [3300], [3400], [3500], [3600], [3700] and [3800]) to all the

modules in the system that support these labels. To transmit the labels, in

section [4004], enter the control panel’s serial number. From the

Destination screen, do not enter a serial number and press [

ACC] if using an

LCD keypad or the center action key (Start) if using a Grafica keypad.

The Module and Label Broadcast feature will only work when a

module is broadcasting its data to a module or to modules of

the same type and

model number. For example, an APR-PRT1

(Printer Module) cannot broadcast to an APR3

-PRT1. Likewise,

a DGP

module cannot broadcast to a DGP2 module.

Module Broadcast Example:

Using an LCD keypad, to program two zone expansion modules

(SN#34540075 and SN#34412100) with the same settings and options of

zone expansion module SN#34540033:

1) Press and hold the [0] key.

2) Enter your [

INSTALLER CODE] and then enter section [4004].

3) Enter 34540033, 34540075, and 34412100 and then press [

ACC].

The control panel automatically copies the contents of 34540033 into the

other two zone expansion modules.

Label Broadcast Example:

Using a Grafica keypad, to copy the labels of the control panel

(SN#020000A2) to all modules that support the labels:

1) Press and hold the [0] key.

2) Enter your [

INSTALLER CODE] and then enter section [4004].

3) Enter 020000A2.

4) From the Destination screen, press the center action key (Start).

The control panel will automatically copy its labels to all supporting modules.

11.16 SYSTEM DATE & TIME

The System Date and Time is programmed through the User Menu, please

refer to Clock Loss in section 15.12.

Option Description Option Description

[1] Partition 1 [5] Partition 5

[2] Partition 2 [6] Partition 6

[3] Partition 3 [7] Partition 7

[4] Partition 4 [8] Partition 8

Keys Description

[STAY]

TEST REPORT: Sends the Test Report report code programmed

in section [3902] to the Monitoring Station.

[FORCE]

CALL WINLOAD: Dials the PC telephone number programmed

in section [3010] to communicate with a computer using

WinLoad.

[ARM]

ANSWER WINLOAD: Forces the control panel to answer a call

made by the Central Monitoring Station that is using WinLoad.

[DISARM]

CANCEL COMMUNICATION: Cancels all communication with

the Monitoring Station or WinLoad until the next reportable event.

[MEM]

INSTALLER TEST MODE: Perform walk tests where the bell or

siren squawks once when a zone opens and twice when it

closes. Press [

MEM] again to exit. Partitions cannot be armed if

the Installer Test Mode is enabled.

[TRBL]

START MODULE SCAN: Verifies the status of modules on the

combus. The LCD Keypads display the serial number of each

module connected to the combus.

[ACC]

START VOLTMETER READING (DGP2-641 only): Verifies if the

combus is supplying sufficient power at the keypad’s location

(refer to the LCD Keypad Reference & Installation Manual).

1 2 ... 30 31 32 33 34 35 36 37 38 39 40 ... 63 64

Comments to this Manuals

No comments

SEKURE DGP2-648 Installation Manual Page 35

Comments to this Manuals

Related products and manuals for Security access control systems SEKURE DGP2-648