SEKURE DGP2-648 Installation Manual download pdf (Page 26)

24 REFERENCE & INSTALLATION MANUAL

8.1 REPORTING ENABLED

ECTION [3036]: OPTION [3]

(Default = disabled) With option [3] ON in section [3036], Event Reporting is

enabled. When an event (e.g. zone in alarm) occurs in the system, the

control panel verifies if a report code was programmed in the section

corresponding to the event. If a report code is programmed, the control panel

dials the Monitoring Station telephone number defined by the Event Call

Direction feature. When the Monitoring Station answers, the control panel

transmits the system account code, followed by the programmed report code.

8.2 REPORT CODES

A report code is a 2-digit or 1-digit hexadecimal value, consisting of digits from

0 to F. For a comprehensive list of the events and their relevant sections,

please refer to the DigiplexNE Programming Guide. Only the Ademco Slow,

Silent Knight, Sescoa and Pager Formats support 1-digit report codes.

When a specific event occurs, the control panel will send the programmed

report code to the Monitoring Station. The method of report code

transmission is defined by the following two items: Reporting Formats

(see section 8.7) and Event Call Direction (see section 8.8). These two

items define how and where the report codes are transmitted. If you are

using the Ademco CID or SIA formats, an Auto Report Code Programming

feature is available (see section 8.15). The following sub-sections provide a

brief description of the events that the control panel can report:

8.2.1 Zone Alarm and Alarm Restore Report Codes

SECTIONS [0201] TO [0296]: FIRST AND SECOND BRACKETS

A report code can be programmed for each of the 96 available zones. Each

section from [0201] to [0296] corresponds to a zone from 01 to 96. The first

set of 2 digits in the sections refer to the Alarm Report Codes that can be

sent to the Monitoring Station to identify which zones generated an alarm.

The second set of 2 digits in the sections refer to the Alarm Restore Report

Codes that can be sent to the Monitoring Station when a zone closes or

once the bell has cut-off after generating an alarm (see section 7.2). Also,

refer to Zone Restore Report Options in section 8.14.

8.2.2 Tamper and Tamper Restore Report Codes

SECTIONS [0201] TO [0296]: THIRD AND FOURTH BRACKETS

A report code can be programmed for each of the 96 available zones. Each

section from [0201] to [0296] corresponds to a zone from 01 to 96. The

third set of 2 digits refer to the Tamper Report Codes that can be sent to the

Monitoring Station to identify which zone experienced a tamper or wire

fault. If the Tamper Recognition Options (see section 7.5) are disabled, the

control panel will not report the occurrence of any tampers or wire faults.

The fourth set of 2 digits refer to the Tamper Restore Report Codes that can

be sent to the Monitoring Station to identify which zone was restored.

8.2.3 Keyswitch Arming

SECTIONS [0701] TO [0732]

A report code can be programmed for each of the 32 keyswitch zones.

Each section from [0701] to [0732] corresponds to a keyswitch from 1 to

32. When using a keyswitch to arm a partition, the control panel can send

the report code to the Monitoring Station identifying which keyswitch was

used. The control panel will not send report codes for keyswitches that are

defined with the PGM Activation definition.

8.2.4 Keyswitch Disarming

SECTIONS [0801] TO [0832]

A report code can be programmed for each of the 32 keyswitch zones. Each

section from [0801] to [0832] corresponds to a keyswitch from 1 to 32. When

a keyswitch is used to disarm a partition, the control panel can send the

report code to the Monitoring Station identifying which keyswitch was used.

The control panel can transmit the report codes every time a partition is

disarmed or only when it is disarmed following an alarm. Also, refer to Disarm

Reporting Options in section 8.13. The control panel will not send report

codes for keyswitches that are defined with the PGM Activation definition.

8.2.5 Access Codes Arming

SECTIONS [2001] TO [2099]

A report code can be programmed individually for each User Access Code

from 01 to 98 in sections [2001] to [2098]. User Access Codes from 99 to

999 use a common report code in section [2099]. When an access code is

used to arm a partition, the control panel can send the report code to the

Monitoring Station identifying which access code was used.

8.2.6 Access Codes Disarming

SECTIONS [2101] TO [2199]

A report code can be programmed individually for each User Access Code

from 01 to 98 in sections [2101] to [2198]. User Access Codes from 99 to

999 use a common report code programmed in section [2199]. When an

access code is used to disarm a partition, the control panel can send the

report code to the Monitoring Station identifying which access code was

used. The report code can be transmitted when a partition is disarmed or

only when disarmed following an alarm. Also, see section 8.13.

8.2.7 Special System Reporting Codes

When the system generates one of the following events, the control panel

can send the report code to the Monitoring Station identifying the event:

8.2.8 Special Arming Report Codes

When the partition arms using a special arming feature, the control panel

can send the report code identifying how the system was armed.

Section Event Description

[3900] Cold Start

control panel re-starts after complete

shutdown (total power loss)

[3901] Warm Start

control panel resets due to sudden

problem other than power loss

[3902] Test Report

report generated automatically

(see section 8.12)

[3903] to [3904] Future Use

[3905] WinLoad Log Off

control panel ends communication with

WinLoad

[3906] Installer In installer enters programming mode

[3907] Installer Out installer exits programming mode

[3908] to [3909] Future Use

Section Event Description

[3910] Auto-Arming when Auto-Arming (see section 6.9)

[3911] PC Arming

system armed using WinLoad or NEware

software

[3912] Late to Close when Auto-Arming (see section 6.9)

[3913] No Movement

when No Movement Auto-Arming

(see section 6.10)

[3914] Partial Arming

when partitions are Stay, Instant or Force

Armed or armed with bypassed zones

[3915] Quick Arming

partitions armed with a One-Touch Arming

feature (see section 6.15)

[3916] Early to Close

partition armed before Arming Report

Schedule (see section 8.3.2)

[3917] Late to Close

partition armed after Arming Report

Schedule (see section 8.3.2)

[3918] Remote Arm

partition armed with the InTouch Voice-

Assisted Arm/Disarm Module (APR3-

ADM2)

[3919]

Closing Delinquency

Partition hasn’t been armed before the

programmed Closing Delinquency Timer

elapsed (see section 8.16).

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 63 64

Comments to this Manuals

No comments

SEKURE DGP2-648 Installation Manual Page 26

Comments to this Manuals

Related products and manuals for Security access control systems SEKURE DGP2-648