SEKURE DGP2-648 Installation Manual download pdf (Page 27)

DIGIPLEXNE CONTROL PANEL 25

8.2.9 Special Disarming Report Codes

When using one of the special disarming features listed below, the control

panel can send the report code to the Monitoring Station identifying how the

system was disarmed. The control panel can transmit the report codes

every time a partition is disarmed or only when it is disarmed following an

alarm. Also, refer to Disarm Reporting Options in section 8.13.

8.2.10 Special Alarm Report Codes

When an alarm is generated, the control panel can send the report code to

the Monitoring Station identifying the type of alarm.

8.2.11 System Trouble Codes

When a trouble is detected, the control panel can send the report code to

the Monitoring Station identifying the type of trouble.

8.2.12 System Trouble Restore Codes

When a trouble described in sections [3940] to [3961] is corrected, the

control panel can send the report code to the Monitoring Station

If the Telephone Line Monitoring (see section 9.1) is disabled,

the control panel will not transmit the TLM report code.

8.3 REPORT ARMING AND DISARMING

The following two features combine to identify when a partition should be

armed and disarmed and enable the control panel to communicate

deviations from the normal schedule to the Monitoring Station.

8.3.1 Enable Arming and Disarming Report Schedules

(Default = disabled) If the partition is armed or disarmed during times not

programmed in the Arming and Disarming Report Schedules (see section

8.3.2), the control panel will send the corresponding report code Early to

Section Event Description

[3920] Cancel Auto-Arm

partition disarms during the Auto-Arm’s

60-sec. delay (see section 6.9)

[3921] Quick Disarm

partition disarms using One-Touch

Disarming feature (see section 6.15)

[3922] PC Disarm

system disarmed using WinLoad or

NEware software

[3923]

PC Disarm after

Alarm

system disarmed using WinLoad or

NEware software after an alarm occurs

[3924] Cancel Alarm

indicates that an alarm was cancelled

even though the system was not armed

when the alarm occurred.

[3925] Future Use Future Use

[3926] Early to Open

partition disarmed before Disarming

Schedule (see section 8.3.2)

[3927] Late to Open

partition disarmed after Disarming

Schedule (see section 8.3.2)

[3928] Remote Disarm

partition disarmed with InTouch Voice-

Assisted Arm/Disarm Module (APR3-

ADM2)

Section Event Description

[3930] Emergency Panic

(non-medical)

the panic keys [1] and [3] were pressed

(see section 7.6)

[3931] Auxiliary Panic

the panic keys [4] and [6] were pressed

(see section 7.6)

[3932] Fire Panic

the panic keys [7] and [9] were pressed

(see section 7.6)

[3933] Recent Closing

an alarm is generated within the Recent

Close Delay (see section 8.10)

[3934] Police Code

Confirmation of an alarm condition

occurred during the Police Code Timer’s

delay (see section 7.4).

[3935]

Auto Zone

Shutdown

the control panel stops regenerating

alarms on a zone during the same armed

period (see section 4.5.1)

[3936] Duress

a Duress enabled access code is keyed in

(refer to the Digiplex/DigiplexNE LCD

Keypad Reference & Installation Manual)

[3937] Keypad Lockout

too many invalid codes entered

(see section 6.17)

Section Event Description

[3940] TLM1 Failure TLM failure on main telephone line

[3941] AC Failure

AC power not detected. Also, see Power

Fail Report Delay in section 8.11

[3942] Battery Failure

battery is disconnected or the battery

voltage is less than or equal to 10.5V

[3943] Auxiliary Supply

the aux power supply’s current is greater

than or equal to 1.1A

[3944]

Bell Output

bell output is disconnected or the current

is greater than or equal to 3A

[3945] Clock Loss panel time lost (see section 11.16)

[3946] Fire Loop Trouble tamper on a fire zone (see section 4.3)

[3947] TO [3949] Future Use

[3950] Bus Fault a module was removed from the combus

[3951] Module Tamper

tamper/wire fault on module (not a motion

detector) on the combus

[3952] ROM Check Error on-board Read-Only Memory trouble

[3953] Module TLM

TLM failure detected on Voice-Assisted

Arm/Disarm Module (APR3-ADM2)

[3954]

Module Fail to

Communicate

DGP2-DVAC failed to communicate with

the Monitoring Station

[3955] Printer Fault Printer Module detected an error

[3956] Module AC Failure no AC power detected on a module

[3957]

Module Battery

Failure

battery on a module is disconnected or the

battery voltage is low

[3958]

Module Auxiliary

Failure

The AUX output on a module has

exceeded current limits

[3959] Future Use Future Use

[3960]

Wireless Trans-

mitter Low Battery

the battery voltage is low on a wireless

transmitter

[3961]

Wireless Module

Supervision Failure

This report code is global unless using the

Contact ID or SIA reporting formats

[3962] to [3964] Future Use

[3965] Fail to Com 1 Phone Number 1 failed to communicate*

[3966] Fail to Com 2 Phone Number 2 failed to communicate*

[3967] Fail to Com 3 Phone Number 3 failed to communicate*

[3968] Fail to Com 4 Phone Number 4 failed to communicate*

* No “Fail to Communicate” for Pager telephone numbers

Section Event Section Event

[3970] TLM1 Restored [3981] Module Tamper Restored

[3971] AC Restored [3982] ROM Check Error Restored

[3972] Battery Restored [3983] Module TLM Restored

[3973]

Auxiliary Supply

Restored

[3984]

Module Fail to Communicate

Restored

[3974] Bell Output Restored [3985] Printer Fault Restored

[3975] Clock Loss Restored [3986] Module AC Failure Restored

[3976] Fire Loop Restored [3987] Module Battery Restored

[3977] Future Use [3988] Module Auxiliary Restored

[3978] Future Use [3989] Future Use

[3979] Future Use [3990]

Wireless Transmitter Battery

Restored

[3980] Bus Fault Restored [3991]

Wireless Module Supervision

Restored

1 2 ... 22 23 24 25 26 27 28 29 30 31 32 ... 63 64

Comments to this Manuals

No comments

SEKURE DGP2-648 Installation Manual Page 27

Comments to this Manuals

Related products and manuals for Security access control systems SEKURE DGP2-648