SEKURE DGP2-648 Installation Manual Page 55
- Page / 64
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
DIGIPLEXNE CONTROL PANEL 53
AC Failure restore 3 3A1 - AC loss restore AR - AC Restoral
Battery Failure restore 3 3A9 - Battery test restore YR - System Battery Restoral
Auxiliary supply trouble restore 3 3AA - System trouble restore YQ - Power Supply restored
Bell output current limit restore 3 321 - Bell 1 restore YH - Bell Restored
Bell absent restore 3 321 - Bell 1 restore YH - Bell Restored
Clock programmed 3 625 - Time/Date Reset JT - Time Changed
Fire loop trouble restore 3 373 - Fire trouble restore FJ - Fire Trouble Restore
Combus fault 1 333 - Expansion module failure ET - Expansion Trouble
Module tamper 1 145 - Expansion module tamper TA - Tamper Alarm
Module ROM_RAM_error 1 3A4 - Rom checksum bad YF - Parameter Checksum Fail
Module TLM trouble 1 352 - Telco 2 fault LT - Phone Line trouble
Module fail to communicate to central station 1 354 - Fail to communicate YC - Communication Fails
Printer fault 1 336 - Local printer failure VT - Printer Trouble
Module AC Failure 1 3A1 - AC loss AT - AC Trouble
Module battery failure 1 3A9 - Battery test failure YT - System Battery Trouble
Module Auxiliary supply trouble 1 3AA - System trouble YP - Power Supply Trouble
Combus fault restore 3 333 - Expansion module failure restore ER - Expansion Restoral
Module tamper restore 3 145 - Expansion module tamper restore TR - Tamper Restoral
Module ROM_RAM_error restore 3 3A4 - Rom checksum bad restore YG - Parameter Changed
Module TLM restore 3 352 - Telco 2 fault restore LR - Phone Line Restoral
Printer fault restore 3 336 - Local printer failure restore VR - Printer Restore
Module AC restore 3 3A1 - AC loss restore AR - AC Restoral
Module battery restore 3 3A9 - Battery test failure restore YR - System Battery Restoral
Module Auxiliary supply restore 3 3AA - System trouble restore YQ - Power Supply Restored
Fail to communicate with central station 1 354 - Fail to communicate YC - Communication Fails
Module RF low battery 1 384 - RF transmitter low battery XT - Transmitter Battery Trouble
Module RF battery restore 3 384 - RF transmitter battery restore XR - Transmitter Battery Restoral
Module RF supervision trouble 1 381 - Loss of supervision - RF US - Untype Zone Supervision
Module RF supervision restore 3 381 - Supervision restore - RF UR - Untyped Zone Restoral
Cold Start 1 3A8 - System shutdown RR - Power Up
Warm Start 1 3A5 - System reset YW - Watchdog Reset
Test Report engaged 1 6A2 - Periodic test report TX - Test Report
PC software communication finished 1 412 - Successful - download access RS - Remote Program Success
Installer on site 1 627 - Program mode Entry LB - Local Program
Installer programming finished 1 628 - Program mode Exit LS - Local Program Success
System Event
Default Contact ID Report Code
for sections [4032] to [4037]
Default SIA Report Code
for sections [4032] to [4037]
- DGP-NE96 1
- TABLE OF CONTENTS 3
- INTRODUCTION 5
- INSTALLATION 6
- DIGIPLEXNE CONTROL PANEL 5 7
- 2.12 KEYPAD ZONE CONNECTIONS 9
- 30m (100ft) 9
- 91m (300ft) 9
- 305m (1000ft) 9
- 2.14 DOUBLE ZONE CONNECTIONS 10
- 2.15 CONNECTING THE DGP2-ZX4 10
- 2.16 COMBUS CONNECTIONS 11
- 2.17 FIRE CIRCUITS 11
- Ω EOL resistor. If a line 11
- 2.19 BUILT-IN RTC 12
- PROGRAMMING METHODS 13
- ZONE PROGRAMMING 14
- 4.2 ZONE DOUBLING (ATZ) 15
- 4.3 ZONE DEFINITIONS 15
- 4.4 ZONE PARTITION ASSIGNMENT 16
- 4.5 ZONE OPTIONS 16
- 4.6 INPUT SPEED 17
- 4.7 EOL ON HARDWIRE ZONES 17
- 4.8 KEYPAD NUMBERING 17
- KEYSWITCH PROGRAMMING 18
- 5.4 KEYSWITCH OPTIONS 19
- ARMING AND DISARMING OPTIONS 20
- DIGIPLEXNE CONTROL PANEL 19 21
- 6.9.1 Auto-Arm Timer 21
- 6.10.1 No Movement Timer 21
- 6.16.1 Exit Delay Termination 21
- 6.17 KEYPAD LOCK-OUT FEATURE 22
- 6.18 BELL SQUAWK 22
- 6.19 RING-BACK 22
- 6.20 MAXIMUM BYPASS ENTRIES 22
- ALARM OPTIONS 23
- 7.6 KEYPAD PANIC OPTIONS 24
- EVENT REPORTING 25
- 8.1 REPORTING ENABLED 26
- 8.2 REPORT CODES 26
- IGIPLEXNE CONTROL PANEL 25 27
- 8.5 ACCOUNT NUMBER 28
- 8.7 REPORTING FORMATS 29
- 8.8 EVENT CALL DIRECTION 29
- DIGIPLEXNE CONTROL PANEL 29 31
- DIALER OPTIONS 32
- PROGRAMMABLE OUTPUTS 33
- SYSTEM SETTINGS AND COMMANDS 34
- DIGIPLEXNE CONTROL PANEL 33 35
- S] and [T] keys to 36
- DIGIPLEXNE CONTROL PANEL 35 37
- ACCESS CODES 38
- 12.6 PARTITION ASSIGNMENT 39
- 12.7 ACCESS CONTROL 39
- ECTION [3038]: OPTION [1] 40
- ECTIONS [2201] TO [2232] 40
- ECTIONS [2601] TO [2615] 40
- ECTIONS [2401] TO [2432] 40
- DIGIPLEXNE CONTROL PANEL 39 41
- WINLOAD SOFTWARE 43
- USER FEATURES 44
- 15.9 KEYPAD SETTINGS 45
- 15.10 EVENT RECORD DISPLAY 45
- 15.12 TROUBLE DISPLAY 45
- 15.13 TROUBLE LATCH 46
- DIGIPLEXNE CONTROL PANEL 45 47
- DIGIPLEXNE CONTROL PANEL 47 49
- DIGIPLEXNE CONTROL PANEL 49 51
- DIGIPLEXNE CONTROL PANEL 51 53
- IGIPLEXNE CONTROL PANEL 53 55
- Sections 57
- DIGIPLEXNE CONTROL PANEL 57 59
- WARNINGS 61
- FCC Warnings 61
- UL and ULC Warnings 61
- CTR-21 Warnings 62
- General Warning 62
- Warranty 62
Related products and manuals for Security access control systems SEKURE DGP2-648
(44 pages)© 2020, manymanuals.com. All rights reserved. | 0.246 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals